I’m looking to expand my printer lineup, and have been looking at kits from magic phoenix for both the Voron Trident and the v2.4R2.

Is there any real benefit to one over the other, or is it more a preference thing?

Edit: if anyone know of other kits, preferably available in the EU, I would also like to take a look at those.

  • Vathsade@lemmy.caEnglish
    5·
    10 months ago

    Looked into this myself, here’s a brief summary of my thoughts:

    V2 has the flying gantry, Trident has the moving base. Primary difference is that since the base (i.e., print surface) is physically secured and rigid to the frame, bed meshes and other alignments should be more consistent. In other words, run a mesh once (or a few times for each of different bed temperatures) and never need to create the mesh again. All else being equal, the flying gantry is a more idealized option since the base in contact with the print is stationary, so very little force is ever seen by the model itself (short of small x and y forces while printing).

    Now the trade off is the significantly added complexity of 4 independent z-motors supporting the gantry. In addition, this requires a gantry alignment macro each time the motors are powered off/on since the gantry sags asymmetrically if the motors aren’t locked (requiring power).

    I have built a V2.4 and found it great, but I don’t know if I personally have found it worth it to have the fixed bed and additional motors. It’s nice to say I did, and it works, but if I needed to make another, I would absolutely go Trident. Cheaper and simpler, and it’s not an ideal world so many of the supposed benefits don’t really make a big difference.

    • DreadPotatoOPEnglish
      2·
      10 months ago

      The weird thing is, the trident kit from magic phoenix is almost $100 more expensive than the V2.4 kit.

      Automatic levelling of the gantry with a macro wouldn’t be a dealbreaker for me, as long as it will give me consistent results without manual adjustments every time.

    • commandar@lemmy.worldEnglish
      11·
      10 months ago

      One thing this overlooks is that the rigid mounted bed of the V2 causes thermal expansion issues. There’s a lot of really bad lore that gets repeated in the community re: bed heater power because the V2 tends to want to taco the bed if it’s heated too quickly.

      The WhoppingOrchard kinematic mounts are a solid option for addressing the issue.

  • commandar@lemmy.worldEnglish
    51·
    10 months ago

    The Trident is the overall better design with a higher performance ceiling.

    Flying gantries are a solution forever in search of a problem. They can work okay and they’re fine at the speeds that were common when the V2 was first designed, but there’s a reason why the community has converged on fixed gantry designs. They’re neat to watch operate but they don’t offer any practical advantage. The V2 tends to be relatively slow by modern standards, especially in terms of accel.

    The Trident isn’t without flaws but it’s a perfectly fine starting point and the huge community does mean that most of the bigger design issues either already have a usermod or somebody working on cooking something up.

  • IMALlama@lemmy.worldEnglish
    4·
    10 months ago

    I went with the v2.4. Why?

    • Build volume. I often ran out of space on my 200mm^3 I3 clone and I wanted the largest build area possible. You can also more easily push Z if you want to by adding a top hat and longer rails
    • No worrying about bent lead screws, etc
    • Easier/simpler bed fans for chamber heating, although there are designs that work on trident
    • A little bit of aesthetics if we’re being honest. That flying gantry looks good IMO

    Quad gantry level is very easy to set up. I’ve never bothered with a bed mesh and, now that I have a better put together stealthburner, only need to fiddle with my z-offset when I change material.

    3 steppers for z vs 4 isn’t a big deal, but there are a few more parts to install and you’ll have to make sure your a/b belts are on the correct side of your z belts. I didn’t find the mechanical build particularly hard.

  • N3Cr0@lemmy.worldEnglish
    3·
    10 months ago

    In theory, the V2 can print a little faster, due to the low center of gravity on the first layers.

    However, the fixed gantry height on the Trident makes it possible to install a fixed part cooling, a lighter print head and go even faster.

    • DreadPotatoOPEnglish
      21·
      10 months ago

      I’m a little bit in favour of the Trident. Mostly due to a simpler construction, I would assume there are fewer things I can mess up.

      • N3Cr0@lemmy.worldEnglish
        21·
        10 months ago

        Agreed. I’m not a V2 owner, but I built a Trident. The V2 is a little overhyped, IMHO.

        In the end, it’s just a matter of your own personal taste though. If you want a highly aesthetic printer with complex mechanics, go for the V2. If you like to keep it simpler without sacrificing much, go with the Trident.

        If you are fine with a smaller device, the V0 may be the right choice. You could reinforce the frame and do a few other mods to achieve insane (yet experimental) print speeds. 1500 mm/s is doable.

      • morbidcactus@lemmy.caEnglish
        1·
        10 months ago

        Both are solid choices, you won’t be upset either way, I was 50/50 on both but decided to do the v2 for 350x350 print area. I have an enclosed mk3s that I use as well, I was putting together a buildtak surface (which I swear by for abs and nylon) for my mk3s and snapped this photo to compare print area size. I still want to do a trident (and maybe convert my mk3s to a switchwire) but I’d build it to match the MK3s wrt bed size and I’d totally consider a bowden extruder.

        All that said, it is markedly faster than the mk3s and I’m definitely no where near pushing it to its limits. There’s a lot to build but I would call it difficult, racking the gantry and belt tensioning being the parts I spent the longest time on. I limit to 24 mm^3/s even though I could go faster, it still just absolutely flies with something like a 0.8mm nozzle. My only other headsup is that modding it is addicting, I’ve thrown on titanium backers and a kinematic mount for the bed, have a whole bunch of other ones in the pipe as well.

        • DreadPotatoOPEnglish
          2·
          10 months ago

          Magic Phoenix actually sells a trident kit with 350x350 build plate, with 250mm Z-axis build size.

          • morbidcactus@lemmy.caEnglish
            1·
            10 months ago

            Big thing for me to do a prusa-sized trident would be the ability to share surfaces between it and my mk3s. 350^2 is nice, I don’t fill it all that often but it’s nice to have the ability to print larger objects.