Interesting point. What about the case where you have your digital volume set to 1%? Would this not squeeze the samples into 1/100 the dynamic range? If I set my volume to 1% it seems to me like those samples now have to all exist within the bottom 1% of the 16b range. Do you not lose at least 5-6 bits of precision on your signal doing this?
You don’t lose precision when you lower the volume (in either an analog or digital realm). You lose actual information!
Let’s say you have a recording you can only listen to with your volume at the 1% setting. Analog or digital, it doesn’t matter.
Your whole system has an acoustic noise floor at something like idk, 10 acoustic decibels. That is a really charitable number because I’ve never measured one that low and it directly corresponds to the loudness of another healthy persons breathing at rest. To give you an idea of how quiet that is, the acoustic decibel scale generally puts a ticking mechanical watch at twice as loud (20 decibels).
I don’t want to talk about decibels because I don’t want to explain the math in the detail I’ve been giving these posts, but we gotta at least cover a little:
Decibels are the measure of sound energy, their scale is logarithmic, so the base of the log function determines how many of decibels make for twice as much.
There are different decibels for measuring in different mediums with different references and they even use different logarithm bases.
Acoustic decibels are log10, so that 20 decibel ticking wristwatch is twice as loud as a person breathing and half as loud as whatever the workplace safety scale says 30 decibels is equivalent to.
Okay so now that we have a floor, we need to establish a ceiling. Let’s say that you did everything right and hooked all your stuff up, turned the volume on the amplifier all the way down, put your headphones, played a maximum volume test tone, maxed out the volume on the software, then turned the amplifiers volume control up until it caused you immediate physical pain. If you have really good hearing, that’s 115 acoustic decibels. Let’s say you got to 120 with the amplifiers volume control up all the way.
Okay, so the noise floor of your headphones on your head is 2^11 as quiet as the loudest sound you can tolerate hearing.
Now you set the volume control to 1%. Doesn’t matter which one. Everything gets 99% quieter. The parts of the signal that were 120 decibels before are now 1.2 decibels. They have been divided by 100, and it’s possible that rounding errors have added .006% error to their harmonic content. .006% of 1.2 is .0072 decibels. Not only is the loudest sound you can stand to hear now quieter than a person breathing, it’s below the noise floor of your system. Far, far below the noise floor. And any rounding error from dividing by 100 is as well!
Okay but what happens when you’re listening to music though? Let’s put aside all that hypothetical stuff and get rockin! Instead of talking about test signals and boring crap, let’s talk about a song!
So same established setup from before, but now you’re listening to a recording of someone playing the banjo while rocking in a chair. There’s a lot of different harmonic content in this signal, the birds chirping, the persons breathing, the wind, the chair creaking the boards of the porch and of course, the instrument itself!
All these different things are at different volumes and they represent components of the harmonic content of the signal you’re listening to. When you turn the recording down, you’re attenuating the signal. All of the signal. If you apply enough attenuation through your chosen volume control to lower the level of the banjo by 40 acoustic decibels then all the other components of the signal are lowered by 40 decibels too. If they were previously 50 acoustic decibels through your headset, they’re part of the noise floor.
The quietest information is simply lost.
Edit: there are massive amounts of information that have been simplified so much as to make this post incredibly inaccurate. Please do not use this as a reference for understanding how we measure or interact with sound. I’m sorry for not going into greater detail but it’s too early to explain the relationship and history of acoustic decibels and decibels per volt.
I’m sorry you have to type so much, I am familiar with most of it, but I appreciate your effort to make sure we’re on the same page without being a douche about it lol. It sounds like we’re saying similar things, but I don’t understand why lower precision is different from losing information. To me, that’s the same thing, it’s a lossy operation.
So the thing is, I have a pair of desktop speakers without any physical volume control that I primarily use for convenience. And for whatever reason, a comfortable listening volume with them is between 1-8% in the OS volume control. I guess the internal amp is just hardwired to be way too loud?
Anyway, I assume that this setup is resulting in objectively lower quality output than if I were to have a 100% signal going to a decent quality DAC/amp with analog volume outputting to the same speakers. And not in a “technically” kind of way, but in a very real “we just crushed the signal into 1/25th of its original scale” way. Would you agree? Am I mistaken?
no worries. i’ve been enjoying going back through this. you’re basically me 25 years ago emailing the winamp ppl to find out what volume control i should use to turn down (for what!).
so there’s a misconception here between compressing a signal and attenuating it. imagine you are looking at a frequency spectrum chart of some song instead of listening to it. it’s got some loud sounds, which show up as big peaks on the chart, and some quiet sounds which show up as small peaks on the chart and there’s a noise floor which is the stuff in the chart that’s not a peak at all.
if you plug a potentiometer in between your signal and the spectrum analyzer and turn down the volume, youll see all the peaks, loud and small, be reduced in amplitude by the same amount. this is called attenuation. the quieter sounds could be reduced until they are part of the noise floor and become imperceptible while the louder sounds would still show up.
it doesnt matter if you achieve attenuation by dividing the 16 bit level component of a stream of samples or by using a resistor as a voltage divider. the quiet and loud sounds are affected equally. those two ways of achieving attenuation function the same because they are performing the same operation.
now lets say you plug a rack mount compressor effects module in between your signal and your spectrum analyzer instead. you could apply more compression to the signal and achieve exactly what you describe, a smaller distance between the quiet and loud sounds, reduction of the original scale, removal of dynamic range, effective bit depth reduction! it would be actual factual “we just crushed the signal into 1/25th of its original scale”.
and if you used a module (or software package) with the capacity for it, you could tie the compression ratio to a gain control so that the compressors output got quieter when you turn the compression ratio up, resulting in more heavily compressed sounds at a quieter volume. that’s a neat little mastering trick to make recordings sound “lively” and “intimate”. makes all those pick scrapes and finger swishes stand out alongside the plucked strings.
you could also do the inverse, make all the quiet sounds louder, so that the guitar is as loud as the kick drums’ transient and it would make your whole song sound much louder and stand out better against background noise in a difficult listening environment like a car radio or cell phone inside a solo cup.
there are even modules that do the opposite, called… expanders! they do what you might expect, increase the dynamic range between loud and quiet sounds. a company called DBX made models for use in home stereos in between tape decks and the amplifier in order to reduce the noise floor of tapes.
but it’s none of that is attenuation, the operation that your volume control provides.
and you’re correct, both compression and attenuation are lossy operations no matter if they’re done with analog electronics or by a microprocessor operating on a buffer somewhere in memory. the difference is that attenuation is literally required to prevent permanent hearing loss and possible equipment damage, while compression is not.
it doesnt matter if you achieve attenuation by dividing the 16 bit level component of a stream of samples or by using a resistor as a voltage divider.
This is the part where I’m not following. In my head, if you’re using analog hardware of sufficient quality, you can attenuate the signal to be very quiet, but still preserve it’s dynamic range. In fact, the DAC is already outputting a very weak, but faithful analog reproduction of the signal, and an amp with a decent S/N ratio is able to bring that very weak signal up to a listening volume without introducing enough noise to matter.
Hypothetically, if for some reason, you took the signal post-amp, used a pot to attenuate it again down to the energy of the post-DAC level, and again ran it through another amp you would theoretically have the same signal still (I understand that in the real world we would start amplifying noise and the signal would degrade, but stick with me). Nothing about the process necessarily introduces noise and thus destroys the signal, you’re only limited to the quality of the components at that point. If you had an infinite chain of theoretically perfect amps and pots, you could repeatedly attenuate and amplify the signal forever without ever losing any quality. It’s an analog process that theoretically preserves the signal, +/- some amount of error due to physics.
Meanwhile, 16b is 16b. If you start shrinking all samples relative to each other (ex. down to 1/64 the original volume, or 10b of resolution), different values inevitably have to clamp to the same values (fitting 64k values into 1024 values), losing information and resulting in poorer quality. If you then try to send that 10b signal through a DAC/amp to achieve the same listening volume that you would have had before digital attenuation, it’s just a 10b signal bit shifted up. All your LSBs are 0s. You can’t possibly attenuate digitally, and then amplify it in any way and hope to get the same signal back. It’s a discrete math process which destroys the signal by design.
the effect of attenuation is the loss of intensity of signal.
loss. it goes away.
attenuation is a lossy process. information in the signal is literally absorbed and radiated away as heat. it cannot be reconstructed because it’s gone.
it isn’t an analog process that theoretically preserves the signal, it’s an analog process that explicitly destroys a component of the signal.
but what if it wasn’t…
okay, lets assume for a second that you have a signal with the same harmonic content as one of my previous examples, a high peak when viewed on a frequency spectrum chart, a low peak when viewed on that chart and everything else. these three parts of the signal represent the loud, quiet and “silent” parts of the signal respectively. unlike the previous example we’ll let our noise floor for the silent parts be infinitely low. for now. so you start hooking up your perfect amps and pots in line and setting them all to 1% or so and listening. it’s sounding pretty good at first, but once you get a few deep, you start getting white noise and clicks and pops and all kinds of craziness.
what the hell! all this equipment is theoretically perfect, why is there noise? it can’t be coming from the perfect equipment!
it’s not. it’s coming from the medium. in our theoretical example all these amplifiers and pots are hooked up with conductive wire. the signal has to propagate through that wire from component to component. atoms of copper are being excited and losing their excitation in proportion to the signal. their state of excitation is being amplified over and over again. the noise is in the wire. by amplifying it over and over again you made it audible. you can’t ever escape it. signed, listening to noise gang. come to my modular synth show.
okay, so now that the possibility of ever attenuating a signal without losing information is hopefully put to rest, lets turn to the digital attenuation of the signal in comparison.
level attenuation over the digital domain is also a lossy process. what’s being misunderstood here is that the levels aren’t being shrunk relative to each other, they’re each being divided and the signal that’s reconstructed by the DAC no longer contains the quiet parts.
just like those quiet parts were absorbed and radiated as heat by the resistor, the digital version of attenuation does away with the need for all that physics crap and simply deletes them from the stream.
if the levels were being shrunk relative to each other, you’d be compressing the signal like when you use the bitcrusher pedal for your guitar and there would be lots of harmonic distortion. but attenuation and compression are different processes and have significantly different results.
consider a quiet sound, your 1/64th volume signal. a sine wave. its encoded to represent 1/64th of the maximum level of the adc’s input because when it was recorded, it represented 1/64th the maximum level of the preamp/microphone/whatever that was plugged into the adc.
is the quiet sine wave of lower quality than one that’s using the full bit depth of the adcs output because it’s intended to represent the maximum level that the adcs input saw from the preamp/microphone/whatever?
of course it isn’t. it just wasn’t loud.
and if your loud sine wave was electrically generated by a theoretical perfect function generator which contains no distortion or other sonic content before being sent to the adc, would it be more damaged if it’s amplitude were divided by 64 before being decoded or if it were decoded and sent through a resistor whose value was chosen specifically to dissipate 63/64ths of it as heat in order to make it as quiet as the quiet sine wave?
of course it wouldn’t.
to your last question, let me rephrase it into something I can agree with: you cannot possibly attenuate and then amplify in any way and hope to get the same signal back. It’s a lossy process which destroys the signal by design.
Ok, the analog attenuation part makes sense now I think. I assumed that an amp increases the amplitude of a signal, and that a pot achieved the inverse (i guess dividing the signal?) but it’s not, it’s effectively subtraction?
Back to my DAC/amp, realistically am I ever intentionally attenuating the analog signal in order to get it to a listening volume? Or am I only ever amplifying it? I think that’s the main difference in my head. If I output my digital signal to the DAC at 100%, and then only ever amplify it to a listening volume, then there’s no way for the signal to be attenuated at all, right?
is the quiet sine wave of lower quality than one that’s using the full bit depth of the adcs output because it’s intended to represent the maximum level that the adcs input saw from the preamp/microphone/whatever?
of course it isn’t. it just wasn’t loud.
No, yeah, that makes sense. I was thinking that, it didn’t matter how strong the signal was, as long as the full sine wave was still present, then quality is preserved. So dividing it down to be a very small voltage, or amplifying it up to be super large, as long as the relative voltages of the signal are retained, we wouldn’t lose any quality (is my, likely flawed, impression).
I think I just don’t know how to think of analog signals. I understand frequency response in theory, but I can’t talk about a signal intuitively in terms of frequency space like you do. Does perfectly amplifying a signal change its frequency response? You don’t have to keep answering, at this point I’m just poking your brain lol.
if you use the volume control on your amp, you’re attenuating the signal. that’s assuming that the amplifier uses a pot as a voltage divider on the input rather than a gain control for the amplifier IC it uses. both are common, but if it’s used as a gain control you’re relying on the linearity of the pot to inform the gain of the amplifier IC and generally frequency linearity across wide gain ranges aren’t fantastic which is why old stuff that used a bunch of discrete transistors instead of chips had set gain and varied the input signal level with an attenuating pot acting as a voltage divider. there are counterexamples. this is complicated.
if you don’t use the volume control on the amp then there’s no attenuation. the downside is that it’s really loud. too loud for safety. too loud for comfort. sometimes too loud for the sustained operation of the equipment.
perfectly amplifying a signal does change its frequency response by adding noise picked up in the process of conveying that signal to and from the perfect amplifier. the noise is added because it’s amplified. there’s some ways to lessen the effect of this, some are effective enough to allow absolutely miniscule signals like those produced by a moving coil phono cartridge to be amplified to tremendous volumes. but there is always noise.
all this talk about amplifiers and volume control is wonderful, but have you considered the stuff that comes after the amplifier? your headphones are a great example: if you pan over to the right channel so that only the right headphone is making sound and slowly pull the headphone away from your ear you’ll hear the frequency response change. the lowest notes will go away, then higher and higher pitched notes will become inaudible until all you hear are tinny high frequency sounds. that’s the effect of attenuation of the sound wave propagating through the air. naturally in air, that attenuation acts as a high pass filter, reducing the volume of the lower pitched notes more than higher pitched notes.
if you pull it away in time with the beat of the music it acts like a bpm synced filter effect or a wah pedal (depending on your age).
the distance from the driver to your ear has an effect on the sound you hear. is that distance correct? everyones heads are a little different…
how about the ears themselves, are they clean? it’s gross to think of, but wax acts just like a pair of earplugs.
and what about your own brain. i’m not even close to versed in psychoacoustics but just imagine agent smith from the matrix saying “you think that’s music you’re listening to?”
there’s nothing wrong with wanting good quality equipment and for it to perform as close to perfect as possible but at some point we’re picking only the most perfectly ripe, unblemished, peak season tomatoes to make salsa.
if you don’t use the volume control on the amp then there’s no attenuation. the downside is that it’s really loud.
Ahhh, I think this is the part I was missing. So I should think of an amp as “injecting” a fixed amount of energy to the signal, way more than I need, and then the volume pot attenuates it back to a comfortable volume. That makes sense since we’ve established that pots attenuate, which necessarily destroy the signal. I still had it in my head that the amount of energy used to amplify the signal was proportional to the volume knob position.
I didn’t know how air affected frequency response, but that makes sense.
As for how clean my ears are, I’m completely deaf, so who cares?
Interesting point. What about the case where you have your digital volume set to 1%? Would this not squeeze the samples into 1/100 the dynamic range? If I set my volume to 1% it seems to me like those samples now have to all exist within the bottom 1% of the 16b range. Do you not lose at least 5-6 bits of precision on your signal doing this?
You don’t lose precision when you lower the volume (in either an analog or digital realm). You lose actual information!
Let’s say you have a recording you can only listen to with your volume at the 1% setting. Analog or digital, it doesn’t matter.
Your whole system has an acoustic noise floor at something like idk, 10 acoustic decibels. That is a really charitable number because I’ve never measured one that low and it directly corresponds to the loudness of another healthy persons breathing at rest. To give you an idea of how quiet that is, the acoustic decibel scale generally puts a ticking mechanical watch at twice as loud (20 decibels).
I don’t want to talk about decibels because I don’t want to explain the math in the detail I’ve been giving these posts, but we gotta at least cover a little:
Decibels are the measure of sound energy, their scale is logarithmic, so the base of the log function determines how many of decibels make for twice as much.
There are different decibels for measuring in different mediums with different references and they even use different logarithm bases.
Acoustic decibels are log10, so that 20 decibel ticking wristwatch is twice as loud as a person breathing and half as loud as whatever the workplace safety scale says 30 decibels is equivalent to.
Okay so now that we have a floor, we need to establish a ceiling. Let’s say that you did everything right and hooked all your stuff up, turned the volume on the amplifier all the way down, put your headphones, played a maximum volume test tone, maxed out the volume on the software, then turned the amplifiers volume control up until it caused you immediate physical pain. If you have really good hearing, that’s 115 acoustic decibels. Let’s say you got to 120 with the amplifiers volume control up all the way.
Okay, so the noise floor of your headphones on your head is 2^11 as quiet as the loudest sound you can tolerate hearing.
Now you set the volume control to 1%. Doesn’t matter which one. Everything gets 99% quieter. The parts of the signal that were 120 decibels before are now 1.2 decibels. They have been divided by 100, and it’s possible that rounding errors have added .006% error to their harmonic content. .006% of 1.2 is .0072 decibels. Not only is the loudest sound you can stand to hear now quieter than a person breathing, it’s below the noise floor of your system. Far, far below the noise floor. And any rounding error from dividing by 100 is as well!
Okay but what happens when you’re listening to music though? Let’s put aside all that hypothetical stuff and get rockin! Instead of talking about test signals and boring crap, let’s talk about a song!
So same established setup from before, but now you’re listening to a recording of someone playing the banjo while rocking in a chair. There’s a lot of different harmonic content in this signal, the birds chirping, the persons breathing, the wind, the chair creaking the boards of the porch and of course, the instrument itself!
All these different things are at different volumes and they represent components of the harmonic content of the signal you’re listening to. When you turn the recording down, you’re attenuating the signal. All of the signal. If you apply enough attenuation through your chosen volume control to lower the level of the banjo by 40 acoustic decibels then all the other components of the signal are lowered by 40 decibels too. If they were previously 50 acoustic decibels through your headset, they’re part of the noise floor.
The quietest information is simply lost.
Edit: there are massive amounts of information that have been simplified so much as to make this post incredibly inaccurate. Please do not use this as a reference for understanding how we measure or interact with sound. I’m sorry for not going into greater detail but it’s too early to explain the relationship and history of acoustic decibels and decibels per volt.
I’m sorry you have to type so much, I am familiar with most of it, but I appreciate your effort to make sure we’re on the same page without being a douche about it lol. It sounds like we’re saying similar things, but I don’t understand why lower precision is different from losing information. To me, that’s the same thing, it’s a lossy operation.
So the thing is, I have a pair of desktop speakers without any physical volume control that I primarily use for convenience. And for whatever reason, a comfortable listening volume with them is between 1-8% in the OS volume control. I guess the internal amp is just hardwired to be way too loud?
Anyway, I assume that this setup is resulting in objectively lower quality output than if I were to have a 100% signal going to a decent quality DAC/amp with analog volume outputting to the same speakers. And not in a “technically” kind of way, but in a very real “we just crushed the signal into 1/25th of its original scale” way. Would you agree? Am I mistaken?
no worries. i’ve been enjoying going back through this. you’re basically me 25 years ago emailing the winamp ppl to find out what volume control i should use to turn down (for what!).
so there’s a misconception here between compressing a signal and attenuating it. imagine you are looking at a frequency spectrum chart of some song instead of listening to it. it’s got some loud sounds, which show up as big peaks on the chart, and some quiet sounds which show up as small peaks on the chart and there’s a noise floor which is the stuff in the chart that’s not a peak at all.
if you plug a potentiometer in between your signal and the spectrum analyzer and turn down the volume, youll see all the peaks, loud and small, be reduced in amplitude by the same amount. this is called attenuation. the quieter sounds could be reduced until they are part of the noise floor and become imperceptible while the louder sounds would still show up.
it doesnt matter if you achieve attenuation by dividing the 16 bit level component of a stream of samples or by using a resistor as a voltage divider. the quiet and loud sounds are affected equally. those two ways of achieving attenuation function the same because they are performing the same operation.
now lets say you plug a rack mount compressor effects module in between your signal and your spectrum analyzer instead. you could apply more compression to the signal and achieve exactly what you describe, a smaller distance between the quiet and loud sounds, reduction of the original scale, removal of dynamic range, effective bit depth reduction! it would be actual factual “we just crushed the signal into 1/25th of its original scale”.
and if you used a module (or software package) with the capacity for it, you could tie the compression ratio to a gain control so that the compressors output got quieter when you turn the compression ratio up, resulting in more heavily compressed sounds at a quieter volume. that’s a neat little mastering trick to make recordings sound “lively” and “intimate”. makes all those pick scrapes and finger swishes stand out alongside the plucked strings.
you could also do the inverse, make all the quiet sounds louder, so that the guitar is as loud as the kick drums’ transient and it would make your whole song sound much louder and stand out better against background noise in a difficult listening environment like a car radio or cell phone inside a solo cup.
there are even modules that do the opposite, called… expanders! they do what you might expect, increase the dynamic range between loud and quiet sounds. a company called DBX made models for use in home stereos in between tape decks and the amplifier in order to reduce the noise floor of tapes.
but it’s none of that is attenuation, the operation that your volume control provides.
and you’re correct, both compression and attenuation are lossy operations no matter if they’re done with analog electronics or by a microprocessor operating on a buffer somewhere in memory. the difference is that attenuation is literally required to prevent permanent hearing loss and possible equipment damage, while compression is not.
This is the part where I’m not following. In my head, if you’re using analog hardware of sufficient quality, you can attenuate the signal to be very quiet, but still preserve it’s dynamic range. In fact, the DAC is already outputting a very weak, but faithful analog reproduction of the signal, and an amp with a decent S/N ratio is able to bring that very weak signal up to a listening volume without introducing enough noise to matter.
Hypothetically, if for some reason, you took the signal post-amp, used a pot to attenuate it again down to the energy of the post-DAC level, and again ran it through another amp you would theoretically have the same signal still (I understand that in the real world we would start amplifying noise and the signal would degrade, but stick with me). Nothing about the process necessarily introduces noise and thus destroys the signal, you’re only limited to the quality of the components at that point. If you had an infinite chain of theoretically perfect amps and pots, you could repeatedly attenuate and amplify the signal forever without ever losing any quality. It’s an analog process that theoretically preserves the signal, +/- some amount of error due to physics.
Meanwhile, 16b is 16b. If you start shrinking all samples relative to each other (ex. down to 1/64 the original volume, or 10b of resolution), different values inevitably have to clamp to the same values (fitting 64k values into 1024 values), losing information and resulting in poorer quality. If you then try to send that 10b signal through a DAC/amp to achieve the same listening volume that you would have had before digital attenuation, it’s just a 10b signal bit shifted up. All your LSBs are 0s. You can’t possibly attenuate digitally, and then amplify it in any way and hope to get the same signal back. It’s a discrete math process which destroys the signal by design.
Would you agree?
the effect of attenuation is the loss of intensity of signal.
loss. it goes away.
attenuation is a lossy process. information in the signal is literally absorbed and radiated away as heat. it cannot be reconstructed because it’s gone.
it isn’t an analog process that theoretically preserves the signal, it’s an analog process that explicitly destroys a component of the signal.
but what if it wasn’t…
okay, lets assume for a second that you have a signal with the same harmonic content as one of my previous examples, a high peak when viewed on a frequency spectrum chart, a low peak when viewed on that chart and everything else. these three parts of the signal represent the loud, quiet and “silent” parts of the signal respectively. unlike the previous example we’ll let our noise floor for the silent parts be infinitely low. for now. so you start hooking up your perfect amps and pots in line and setting them all to 1% or so and listening. it’s sounding pretty good at first, but once you get a few deep, you start getting white noise and clicks and pops and all kinds of craziness.
what the hell! all this equipment is theoretically perfect, why is there noise? it can’t be coming from the perfect equipment!
it’s not. it’s coming from the medium. in our theoretical example all these amplifiers and pots are hooked up with conductive wire. the signal has to propagate through that wire from component to component. atoms of copper are being excited and losing their excitation in proportion to the signal. their state of excitation is being amplified over and over again. the noise is in the wire. by amplifying it over and over again you made it audible. you can’t ever escape it. signed, listening to noise gang. come to my modular synth show.
okay, so now that the possibility of ever attenuating a signal without losing information is hopefully put to rest, lets turn to the digital attenuation of the signal in comparison.
level attenuation over the digital domain is also a lossy process. what’s being misunderstood here is that the levels aren’t being shrunk relative to each other, they’re each being divided and the signal that’s reconstructed by the DAC no longer contains the quiet parts.
just like those quiet parts were absorbed and radiated as heat by the resistor, the digital version of attenuation does away with the need for all that physics crap and simply deletes them from the stream.
if the levels were being shrunk relative to each other, you’d be compressing the signal like when you use the bitcrusher pedal for your guitar and there would be lots of harmonic distortion. but attenuation and compression are different processes and have significantly different results.
consider a quiet sound, your 1/64th volume signal. a sine wave. its encoded to represent 1/64th of the maximum level of the adc’s input because when it was recorded, it represented 1/64th the maximum level of the preamp/microphone/whatever that was plugged into the adc.
is the quiet sine wave of lower quality than one that’s using the full bit depth of the adcs output because it’s intended to represent the maximum level that the adcs input saw from the preamp/microphone/whatever?
of course it isn’t. it just wasn’t loud.
and if your loud sine wave was electrically generated by a theoretical perfect function generator which contains no distortion or other sonic content before being sent to the adc, would it be more damaged if it’s amplitude were divided by 64 before being decoded or if it were decoded and sent through a resistor whose value was chosen specifically to dissipate 63/64ths of it as heat in order to make it as quiet as the quiet sine wave?
of course it wouldn’t.
to your last question, let me rephrase it into something I can agree with: you cannot possibly attenuate and then amplify in any way and hope to get the same signal back. It’s a lossy process which destroys the signal by design.
Ok, the analog attenuation part makes sense now I think. I assumed that an amp increases the amplitude of a signal, and that a pot achieved the inverse (i guess dividing the signal?) but it’s not, it’s effectively subtraction?
Back to my DAC/amp, realistically am I ever intentionally attenuating the analog signal in order to get it to a listening volume? Or am I only ever amplifying it? I think that’s the main difference in my head. If I output my digital signal to the DAC at 100%, and then only ever amplify it to a listening volume, then there’s no way for the signal to be attenuated at all, right?
No, yeah, that makes sense. I was thinking that, it didn’t matter how strong the signal was, as long as the full sine wave was still present, then quality is preserved. So dividing it down to be a very small voltage, or amplifying it up to be super large, as long as the relative voltages of the signal are retained, we wouldn’t lose any quality (is my, likely flawed, impression).
I think I just don’t know how to think of analog signals. I understand frequency response in theory, but I can’t talk about a signal intuitively in terms of frequency space like you do. Does perfectly amplifying a signal change its frequency response? You don’t have to keep answering, at this point I’m just poking your brain lol.
if you use the volume control on your amp, you’re attenuating the signal. that’s assuming that the amplifier uses a pot as a voltage divider on the input rather than a gain control for the amplifier IC it uses. both are common, but if it’s used as a gain control you’re relying on the linearity of the pot to inform the gain of the amplifier IC and generally frequency linearity across wide gain ranges aren’t fantastic which is why old stuff that used a bunch of discrete transistors instead of chips had set gain and varied the input signal level with an attenuating pot acting as a voltage divider. there are counterexamples. this is complicated.
if you don’t use the volume control on the amp then there’s no attenuation. the downside is that it’s really loud. too loud for safety. too loud for comfort. sometimes too loud for the sustained operation of the equipment.
perfectly amplifying a signal does change its frequency response by adding noise picked up in the process of conveying that signal to and from the perfect amplifier. the noise is added because it’s amplified. there’s some ways to lessen the effect of this, some are effective enough to allow absolutely miniscule signals like those produced by a moving coil phono cartridge to be amplified to tremendous volumes. but there is always noise.
all this talk about amplifiers and volume control is wonderful, but have you considered the stuff that comes after the amplifier? your headphones are a great example: if you pan over to the right channel so that only the right headphone is making sound and slowly pull the headphone away from your ear you’ll hear the frequency response change. the lowest notes will go away, then higher and higher pitched notes will become inaudible until all you hear are tinny high frequency sounds. that’s the effect of attenuation of the sound wave propagating through the air. naturally in air, that attenuation acts as a high pass filter, reducing the volume of the lower pitched notes more than higher pitched notes.
if you pull it away in time with the beat of the music it acts like a bpm synced filter effect or a wah pedal (depending on your age).
the distance from the driver to your ear has an effect on the sound you hear. is that distance correct? everyones heads are a little different…
how about the ears themselves, are they clean? it’s gross to think of, but wax acts just like a pair of earplugs.
and what about your own brain. i’m not even close to versed in psychoacoustics but just imagine agent smith from the matrix saying “you think that’s music you’re listening to?”
there’s nothing wrong with wanting good quality equipment and for it to perform as close to perfect as possible but at some point we’re picking only the most perfectly ripe, unblemished, peak season tomatoes to make salsa.
Ahhh, I think this is the part I was missing. So I should think of an amp as “injecting” a fixed amount of energy to the signal, way more than I need, and then the volume pot attenuates it back to a comfortable volume. That makes sense since we’ve established that pots attenuate, which necessarily destroy the signal. I still had it in my head that the amount of energy used to amplify the signal was proportional to the volume knob position.
I didn’t know how air affected frequency response, but that makes sense.
As for how clean my ears are, I’m completely deaf, so who cares?
jk 😁. Thanks for the talk, I learned some things!